1310T - Composites
A non-draining, 100% solids epoxy system for producing fiber reinforced epoxy composites. A single resin (Rhino™ 1310T) with available choices of curing agents provides the maximum flexibility for a variety of fiber reinforced applications. A wide variety of Rhino™ hardeners are available to use with Rhino™ 1310T epoxy resin, see chart below.
1310T Resin for Composite Infrastructure
Rhino 1310T epoxy composites are non-draining, 100% solids systems that provide maximum flexibility for a variety of reinforced composites. Whether performing fiberglass infrastructure reinforcement, seismic retrofits, or the repair of failing conventional concrete/rebar structures, Rhino 1310T forms a matrix in which carbon or glass fiber is saturated then woven together to add structural reinforcement.
Rhino fiberglass infrastructure reinforcement and seismic retrofits last longer and incur a fraction of the cost and time it takes to achieve the same results using conventional materials and techniques. Carbon fiber wrap and blast mitigation solutions are currently being used in numerous concrete, masonry, steel, and wood structures to increase strength and durability.
Features & Benefits
• Fast wet-out of fiberglass reinforcements with minimal drainage from lamination
• Greater fatigue resistance, strength and reinforcement
• Flexible carbon fiber wrap conforms to any shape
• Less weight and lower thermal expansion
• Reduced installation time
• Carbon fiber or glass filiment winding (pressure tanks, vessels)
• Fatigue resistant FRP manufactured parts
• Composite tooling
• Blast Mitigation
• Construction Equipment
• Bridges and piers
• Fuel tank sealers
Allow the composite to cure at the recommended temperature as listed in the physical properties chart (above). In the case of all listed hardeners, allow at least 6-8 hours at ambient (>65°F) or 2-3 hours at 130°F before attempting to return the composite to service. In colder weather (less than 65°F) allow additional time for the composite to cure.
After the recommended elevated temperature cure, all systems may be exposed to the listed service temperatures. In all cases, an elevated temperature cure of 2-4 hours at 120°F - 140°F assures the highest quality end product.
Liquid and cured physical properties of 1310T with Rhino hardeners:
|RHINO 1310T Composite Resin with:||Hardeners|
|Parts Hardener by Weight||22||22||22||43||20|
|Mix Ratio by Volume||4:1||4:1||4:1||2:1||5:1|
|Gel Time Min (150gr)||12-15||30-35||50-60||60-70||25-30|
|Set Time, Hrs @ 77°F||2||4||5||4||3|
|Cure Time, Hrs @ 130°F||2||3||4||3-4||3-4|
|Shore D Hardness (24 hr room temp cure)||80||78||80||75||85|
All hardeners reach sufficient strength for return to service or demolding after an overnight ambient cure. The fastest Rhino hardener, Rhino 3102, is useful for winter applications, or for mixing in smaller batches. Rhino 3103 is the standard 30-minute system hardener used for 4:1 volume mixing applications. Rhino 3138 should be used in high temp applications (up to 240˚F) and is 4:1 by volume, which is also useful in hot weather or for large areas. Rhino 3191 is our standard 1 hour General Purpose hardener, and may be certified to NSF Standard 61 for potable water.
Rhino 3136R-1 is used for composite tooling. Rhino hardeners, 3102, 3103 and 3191 are DOT not regulated / DOT non-corrosive, minimizing hazardous materials shipping issues.
Technical Mechanical Properties
Rhino 1310T resin post cured at 130°F for 4 hours with all listed hardeners. For reference purposes only, these properties are measured as a composite using A-260 unidirectional e-glass, glass to resin ratio of 60:40.
|Tensile Strength (psi)||>30,000||ASTM D-638|
|Flexural Strength (psi)||>32,000||ASTM D-790|
|Compressive Strength (psi)||>20,000||ASTM D-695|
|Izod Impact Strength (ft/lb/in)||>40||ASTM D-256A|
|Heat Deflection Temp||>170°F||RHINO|